s355j2g3 chemical composition

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S355J2G3 can be supplied as steel plate/ sheet, round steel bar, steel

EN S355J2G3 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86 13880247006

Sep 20, 2017 · S355J2G3 steel Chemical composition,S355J2G3 steel Mechanical properties S355J2G3 steel is a carbon manganese steel. It is characterised by its excellent strength and weldability. S355J2G3 is a non alloy structural steel according to EN10025:1990.

Steel grade:EN10025 S355J2G3 DimensionThickness 5 300mm, Width 1500 3500mm, Length 3000 12000mm ApplicationMainly used for making axles, bolts and connecting rods, motor, hydraulic and pump shafts, machinery parts etc. S355J2G3 chemical composition:

Bebon International is a professional S355J2G3 Chemical analysis ,S355J2G3 steel exporter and a steel Stockist in china.

The presented S355J2G3 High Tensile EN 10025 Sheets is factory made by using soaring grade of raw material and cutting edge technology that make sure in giving high performance. These S355J2G3 High Tensile EN 10025 Plates are pared for actuation by manual, wet

Main chemical composition in EN 10025 S355J2G3 steel is carton max 0.22, silicon max 0.55, manganese max 1.60, phosphorus max 0.035, sulphur max 0.035, chromium max 0.30. More detailed information about S355J2G3 steel, please refer to the down table:

S355J2G3 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. With its low carbon equivalent, it possesses good cold forming properties. The plate is produced by fully killed steel process and supplied in normalized or controlled rolling condition.

S355J2G3 steel plate is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. S355J2G3 steel, S means structural steel,355 is mean minimum yield strength of 355 N/mm²,J2 symbol 20 temperature impact test, G3 symbol for normalized.

Chemical composition of steel S335J2G3 (1.0570), Standards of steel S335J2G3 (1.0570) Mechanical Properties of steel S335J2G3 (1.0570) Equivalent grades of steel S335J2G3 (1.0570) steel S335J2G3 (1.0570) Tensile Strength, Elongation, Proof strength , Hardness

Sep 20, 2017 · S355J2G3 steel Chemical composition,S355J2G3 steel Mechanical properties S355J2G3 steel is a carbon manganese steel. It is characterised by its excellent strength and weldability.

S355J2G3 EN 10250 2 (Euronorm) Chemical composition C < 0.22 Si < 0.55 Mn < 1.6 P < 0.035 S < 0.035 Cr < 0.3 Mo < 0.08 Ni < 0.3 Al > 0.02 Fe Rest For grain refining can contain Al, Ti, V, Nb singly or in combination. Cr + Mo + Ni < 0.48% Properties By EN 10250 2 Normalizing temperature 890 950 °C Normalized and normalized and tempered condition Longitudial test pieces

Main chemical composition in EN 10025 S355J2G3 steel is carton max 0.22, silicon max 0.55, manganese max 1.60, phosphorus max 0.035, sulphur max 0.035, chromium max 0.30. More detailed information about S355J2G3 steel, please refer to the down table:

S355J2G3 is the EN chemical designation. It has a moderately high electrical conductivity among wrought carbon or non alloy steels. In addition, it has a moderately low thermal conductivity and a moderately low ductility.

S355J2G3 is a non alloy structural steel according to steel standard EN10025:1990. This standard has now been replaced by EN10025 2:2004 and steels with the S355J2G3 designation are now known as S355J2.J2 means minus 20 centigrade impacting test,G3 means supplying condition and deoxidation measures (Semikilled steel).

Aug 23, 2015 · S355 is named based on it's minimum yield strength of 355 Mpa (N/mm2), However the yield strength reduces when you go up in thickness above 16 mm for flat products & hollow sections. Here is the table showing reduction in yield strength based on thickness. Up to 16 mm 355 Mpa. 16 mm < t 40 mm 345 Mpa.

S355J2 Steel Grade, Mechanical Properties, Chemical Composition, Grade Equivalent StandardEN 10025 2:2004, European standard for hot rolled structural steel. Part 2 Technical delivery conditions for non alloy structural steels.

Steel Plate. A588 GrA (Grade A), A588 GrB(Grade B) Weathering, Corrosion Resistant Steel Plate; S355J2+N and S355J2G3 are the same steel grades as both grades delivery condition are normalized. G3 and N stand for normalized. Chemical Composition C.E. C Si Mn Cr Mo

Chemical composition of steel S355J2 (1.0577), Standards of steel S355J2 (1.0577) Mechanical Properties of steel S355J2 (1.0577) Equivalent grades of steel S355J2 (1.0577) steel S355J2 (1.0577) Tensile Strength, Elongation, Proof strength , Hardness.

May 11, 2012 · Chemical Composition of Structural Steels S235, S275 and S355. The Chemical composition of Structural Steel is extremely important and highly regulated. It is a fundamental factor which defines the Mechanical properties of the steel material.

S355J2G3 W.Nr. 1.0570 General size range Ø 5,5 1000 mm Chemical composition C=max.0,20* Si=max.0,55 Mn=max.1,60 P=max.0,035 S=max.0,035 Cr=max.0,30 Al=min.0,020 Cu=max.0,30 Ceq=max.0,45** Ni=max.0,30 *C=max.0,22% for sizes over 40 mm **Ceq=max.0,47% for sizes 40 150 mm, Ceq=max.0,49% sizes over 150 mm Grade equivalents Similar grades

S355J2 steel is a carbon manganese,high yield non alloy steel. It is called S355 because of the average minimum yield for this material is 355 Mpa.As a structural steel,it has excellent strength and weldability.It can be readily welded to other weldable steel. For its low carbon equivalent, it possesses good cold forming properties.

Precision Steel Contents Brief portrait Technical features Chemical composition Mechanical properties General thickness tolerances Delivery options Structural steel General structural steels are standardized in accordance with DIN EN 10025. Through appropriate temperature control during hot rolling BU Precision Steel supplies