1035 steel equivalent

for Steel 1035 (AISI, ASTM, UNS) and its European equivalent C35R (1.1180) (EN)

Both ASTM A36 carbon steel and SAE AISI 1035 steel are iron alloys. Their average alloy composition is basically identical. There are 31 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown.

C1035 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength, toughness and wear resistance.

AISI 1035 is a water resisting carbon steel whose wear resistance and hardenability are increased by the addition of small quantity of chromium. The following sections will discuss in detail about AISI 1035 carbon steel. Chemical Composition. The chemical composition of AISI 1035 carbon steel is outlined in the following table.

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. 1035 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

21 rows · Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier.

SAE AISI 1035 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1035 is the designation in both the SAE and AISI systems for this material. G10350 is the UNS number. The properties of SAE AISI 1035 steel include two common variations. This page shows summary ranges across both of them.

Jul 24, 2010 · Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

1035 carbon steel is not equivalent to ASTM A 36 structural steel. The reason is that the carbon content for A36 structural steel is normally below 0.35% carbon content by mass for weldability.

Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

Carbon Steel Grade 1035. AISI 1035 Carbon Steel, cold drawn, 19 32 mm (0.75 1.25 in) round. SubcategoriesCarbon Steel; AISI 1000 Series Steel; Medium Carbon Steel.

Jul 24, 2010 · Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

1035 steel bar is most commonly characterized as a medium carbon grade, and as such is a popular work horse grade of steel. 1035 steel bar is often supplied in hot rolled, cold drawn, turned & polished, annealed and or coated conditions;  both in bar lengths or packaged into wire rod.

USA Japan Germany U. K. France Italy Spain Sweden China; AISI/SAE JIS W. nr. DIN BS EN AFNOR UNI UNE SS GB; A570.36STKM 12A STKM 12C1.0038RSt.37 24360 40 C E 24 2 Ne

AISI 1035 steel is a medium tensile steel supplied in the black hot rolled or normalized condition. It has Brinell hardness ranging between 170 and 210 and tensile strength of 570 700 MPa.

Properties of steel C35 (1.0501) WeldabilityIt can be welded quite well without any precautions. HardenabilityLow hardenability; core quenching in water till a diameter of 12 15 mm; as far as bigger diameters are concerned, it hardens only till a certain depth, inversely proportional to diameter, like all nonalloy steels with medium high carbon content.

ASTM A36 Mild Steel ASTM A36 Standard Specification for Carbon Structural Steel covers carbon structural steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.

High Yield Steel High yield strength cold forming steels Simple pressure vessels steel Stamping and cold forming steels Steel for Boilers and Pressure Vessels Steel for gas cylinders and gas vessels Steel for large diameter pipes Steel For Ship BuildingSteel for welded tubes Steel Resistant to Atmospherical corrossion Steel with Cr., Mo.,Cr Mo.

MARYLAND METRICS Technical Data Chart A short general listing of popular materials International Material Grade Comparison Table The standards that correspond with DIN Material Numbers can only be compared approximately. The use of these equivalents has to be evaluated on a case by case basis.

Equivalent Grades Equivalent Grades Exporter Contact Us For High Quality Equivalent Grades. At JB Steel we pride ourselves on always putting the customer first. We help make stainless solutions simple for you by ensuring satisfaction through high delivery

Some equivalent standards may be stricter whereas others may be outside the bounds of the original standard. Find a supplier We can help you find a supplier of ASTM A576 Grade 1035

EQUIVALENT CROSS SECTION BY BAR SIZE AND SHAPE 163 HOT ROLLED BAR WEIGHTS 164 HOT ROLLED BAR REDUCTION RATIOS AT SDI 167 STEEL PROPERTIES GRAIN SIZE 171 EFFECTS OF ALLOYING ELEMENTS ON STEEL PROPERTIES 172 Steel Dynamics Engineered Bar Products Division attained ISO 9001:2000 certification in September 2004.

AISI 1035 SAE UNS G10350 Carbon Steel Foundry. Steel foundry in China for producing AISI 1035 SAE UNS G10350 Carbon Steel castings. The followings are this material's chemical composition, physical and mechanical properties and equivalent material grades. The following sections will discuss in detail about AISI 1035 carbon steel.

With DuoNian production experience, strict control 1.1181, DIN Ck35, AISI 1035 chemical composition and 1.1181, DIN Ck35, AISI 1035 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers.